HGLRC-FLIPSKY FSESC6.6 based upon VESC® 6
FSESC6.6 with firmware version 3.37, compatible with Benjamin VESC TOOL, can be used for models, multi-axis aircraft, electric vehicles, electric skateboards, golf carts, smart cars, robots, and simple industrial position control.
- Hardware: V 6.6
- Firmware: V3.37
- Voltage: 6V - 60V (Safe for 3S to 12S LiPo)
- Voltage spikes may not exceed 60V
- Current: Continuous 60A, Burst 150A. Values depend on the temperature and air circulation around the device
- 5V 1.5A output for external electronics
- 3.3V 1A output for external electronics
- Modes: DC, BLDC, FOC (sinusoidal)
- Supported sensors: ABI, HALL, AS5047
- include Anti-spark switch
- include Waterproof aluminum case
The package contains:
1*FSECS6.6 + Aluminium case
1*USB micro Flash Charge VOCC Cable
1*Mini Micro JST 2.0 PH 3-Pin Connector plug with Wires Cables
1. Power advantage
In order to effectively and safely protect the power contact from oxidation caused by electric spark burn and the electronic components of integrated circuits from breakdown and to prevent the occurrence of an electric spark which may cause explosion, we added an anti-spark switch to the front of the power supply to allow a maximum current to pass up to 300A. Also, it’s more convenient to use.
In order to make the power supply filter better and the voltage more stable, we replaced the original C46 and C47 with large electrolytic capacitors with larger capacity and better energy storage. Meanwhile, C37 ,C39 ,C41,C40,C43,C44 were all replaced by 10uF 100V with High voltage capacitors. In this way, the voltage change of the MOS becomes more stable and efficient.
2. Processing Advantages of GND on the Circuit
In order to better handle the large current GND and the mutual interference between the GND of the MCU circuit and the GND of the NRF circuit, we added three O ohm resistors to better achieve the filtering effect.
3. Output optimization of Power Supply 3.3V
Replaced the LM3671 chip with the two-channel MIC5219-3.3YM5, upgrading from the original 3.3V, 600MA to 500MA*2=1A output, better supply power to peripherals, meanwhile, adding two IN5819 diode rectifiers to achieve 3.3V for short-circuit protection, replace the C9 2.2uF on the capacitor with 10uF and add a 4.7uF filter capacitor.
4. Output optimization of Power Supply 5V
Replacing capacitor C31 2.2uF with 22uF
5. Other optimization
Replacing capacitor C15 2.2uF with 22uF
6. Optimization of Mosfet
12 Power MOSFETs NTMFS5C628NL is specially processed on heat dissipation and over-current to achieve continuous 80A output and more stable performance.
7. Optimization of PCB layout and process
1). The PCB adopts a gold-thickening process with a 6-layer PCB layout design. The thickness of each layer of copper foil is 3OZ, and the total copper foil thickness is 3OZ*6=18OZ. meanwhile, the PCB increases heat dissipation and the over-current treatment process at key part--sunken sunroof, making the overall effect better and having more advantages!
2).PCB size layout is more convenient to use. We integrated the XT60, XT90, banana connector 4.0 and so on, making the overall looks more beautiful.
8. aluminum case
Using aluminum case with aviation-grade aluminum alloy material. It's anodized to ensure that it has good heat dissipation, while achieving IP65 waterproof level.
- Measure current and voltage of all phases
- Regenerative braking
- Traction control (single and double settings)
- Sensor or sensorless operation + hybrid mode
- Configurable RPM, Current, Voltage and Power Limits
- Input source: PPM, simulation, NRF Nyko Kama Nunchuck
- Communication ports: USB, CAN, UART, NRF, Bluetooth
- Throttle curves and ramps for all input sources
- Separate acceleration and brake throttle curves
- Seamless four-quadrant operation
- Motor speed, ampere hours, watt hour count
- Instant data analysis and reading via communication port
- Adjustable different protections:
- Low input voltage
- High input voltage
- High motor current
- High input current
- High regenerative braking current (separate limit of motor and input)
- High speed (separate limit in each direction).
- Over temperature (MOSFET and motor)
Please read all the items in this warranty before submitting a claim with HGLRC customer service. Failure to do so will result in claim being delayed or may be rejected.
HGLRC 6-month limited warranty
HGLRC guarantees this product to be free from defects in materials or workmanship for 6-month from the original date of purchase verified by sales receipt (not when product started to be in use).
Warranty claims will not cover the following:
- No purchasing record from HGLRC orauthorized dealers
- Cut off original power plug or not using reverse polarity protected plugs
- Wire damaged
- Any crash damage
- Humidity/Water inside
- Mechanical damage of electronical components/PCB
- Soldered on the PCB (except on external solder-tabs) and incorrect soldering
If you have issues with soldering to smaller components…. STOP. Please seek professional assistance before attempting.
Connected speed-control with reversed polarity. There are special components that are in use to detect when this happens.
No warranty shall apply to any product that has been subject to misuse, improper testing, assembly, mishandling, or which has been operated contrary to current instructions relating to installation or maintenance or operation from the use of any equipment purchased form this store.
It is the buyer’s responsibility to use the items safely and legally and to take proper measures to prevent any damage to person or property from the use of the equipment.
Please report any problems you are having to us via a support ticket from the product purchasing account. Please do not ship items back prior before contacting us and receiving a return authorization.*Repair available in China and US
*Out of 6-month Warranty Period may be accepted
*Damaged item reparable or not will be assessed
*Free charge for repair excluding shipping
*The duration of the repair will depend on the extent of the damage and the availability of its parts.
Return Policy (RMA)*RMA# (to be issued to you)
*30 days for return from the date of purchase
*Purchasing record is required
*Shipment of incorrect product by fulfillment mistakes will be accepted
*Returned items that are rendered unsellable as a new product will be rejected.
Returns of opened packages may be accepted under some rare situations, but may be subject to a restocking fee or rejected depending on the condition of the items.
Customers returning defective items will receive either a replacement, a store credit, or a refund. Orders are eligible for refund up to 30 days after the order was shipped, otherwise store credit or replacement may be issued.
Returns of products in good working order will receive a refund for the price of the item only, not the shipping costs.
Full refund requires:
*Within 30 days of purchase
*Product in new condition with no wear
*All packaging included and intact
As parts of complex systems, failure of one component can result in a crash or damage to other items. HGLRC is not responsible in any way, for damage to other equipment due to a failure of a component in a system.